FluidMaster 747 Floating Fill Valve

1. პროდუქტი დასრულდაview

The FluidMaster 747 Floating Fill Valve is a high-quality, universal replacement valve designed for efficient and quiet water refilling in both concealed and exposed plastic and ceramic toilet cisterns. Engineered for reliability and ease of installation, this valve is suitable for a wide range of plumbing systems, operating effectively under both high and low water pressure conditions. Its self-cleaning mechanism ensures long-term performance with minimal maintenance.

FluidMaster 747 Floating Fill Valve

2. ძირითადი მახასიათებლები

• რეგულირებადი სიმაღლე: The valve height can be adjusted from 230 mm to 355 mm, allowing for flexible installation in various cistern sizes.
• მრავალმხრივი თავსებადობა: Suitable for both high and low water pressure systems, functioning reliably from 0.5 bar minimum to 10 bar maximum pressure.
• Extremely Quiet Operation: Classified as Noise Class 1, operating at ≤20 dB(A) for a silent refill experience.
• Fast Filling: Optimized mechanics ensure rapid refilling of the toilet cistern.
• Self-Cleaning Mechanism: Features a unique mechanism for reduced maintenance and prolonged lifespan.
• მარტივი ინსტალაცია: Designed for quick and straightforward mounting.
• Durable Brass Connector: Equipped with a G 3/8" x 35 mm brass connector for a robust and secure connection.
• კომპაქტური დიზაინი: Efficiently designed to fit into various cistern configurations.

Detailed diagram of the FluidMaster 747 valve, showing key components like the brass shank, water level adjusting screw, and diffuser, along with dimensions.

3. დაყენება და ინსტალაცია

Follow these steps for proper installation of your FluidMaster 747 Fill Valve:

1. წყალმომარაგების გამორთვა: Locate the water shut-off valve for your toilet, usually near the base, and turn it clockwise until the water flow stops.
2. Empty Cistern: Flush the toilet to drain the water from the cistern. Hold the flush handle down to ensure as much water as possible is removed.
3. ძველი სარქვლის ამოღება (ასეთის არსებობის შემთხვევაში): Disconnect the water supply line from the old fill valve. Unscrew the locknut from underneath the cistern that secures the old valve, then remove the old valve.
4. Insert New Valve: Place the FluidMaster 747 fill valve into the hole at the bottom of the cistern. Ensure the shank is properly seated.
5. უსაფრთხო სარქველი: From underneath the cistern, thread the provided locknut onto the valve shank and tighten it by hand. Do not overtighten, as this can damage the cistern or valve.
6. წყალმომარაგების დაკავშირება: Attach the water supply line to the brass connector (G 3/8" x 35 mm) at the base of the new fill valve. Tighten securely by hand, then use a wrench for a final quarter-turn, being careful not to overtighten.
7. სიმაღლის რეგულირება: The valve's height can be adjusted by twisting the upper section or using the water level adjusting screw (refer to product diagrams). Adjust the valve so that the critical level mark is above the overflow pipe.
8. წყალმომარაგების აღდგენა: Slowly turn the water shut-off valve counter-clockwise to restore water flow to the cistern. Check for any leaks around the connections.
9. წყლის დონის რეგულირება: Allow the cistern to fill. If the water level is too high or too low, fine-tune the float mechanism using the water level adjusting screw until the desired water level is achieved (typically about 1 inch below the top of the overflow pipe).

Visual guide for installing the FluidMaster 747 valve, showing key installation steps.

Illustration demonstrating the FluidMaster 747 valve's compatibility with various toilet cisterns and a list of included components.

4. საოპერაციო ინსტრუქციები

The FluidMaster 747 Floating Fill Valve operates automatically. Once installed and the water supply is turned on, the valve will sense the water level in the cistern. After each flush, as the water level drops, the float mechanism will activate the valve, allowing water to refill the cistern to the pre-set level. The valve will then shut off, maintaining the desired water volume for the next flush.

Ensure the water level is adjusted correctly during installation for optimal flushing performance and water conservation.

5. მოვლა

The FluidMaster 747 valve features a self-cleaning mechanism designed to minimize the need for frequent maintenance. However, periodic checks can help ensure its longevity and efficient operation:

• რეგულარული შემოწმება: Periodically inspect the valve for any signs of wear, debris, or mineral buildup, especially in areas with hard water.
• დასუფთავება: If you notice slow filling or reduced performance, turn off the water supply and gently clean any visible debris from the valve's inlet screen or float mechanism.
• მოერიდეთ მკაცრ გამწმენდებს: გაფრთხილება: Do not use in-tank, drop-in toilet bowl cleaners containing bleach or chlorine. Use of such products can result in damage to tank components and property, and may void the Fluidmaster warranty. Always use quality Fluidmaster parts when installing or repairing.

6. Დიაგნოსტიკა

If you encounter issues with your FluidMaster 747 Fill Valve, refer to the following common problems and solutions:

7. სპეციფიკაციები

8. გარანტია და მხარდაჭერა

Specific warranty details for this product are not provided in the available information. For warranty claims, technical support, or further inquiries, please contact Fluidmaster customer service directly or visit their official webსაიტი.

ოფიციალური Webსაიტი: www.fluidmaster.com