E-LINTER Pear Pro ETH Plus WiFi Plus BLE Stick მონაცემთა ჟურნალი
შესავალი
The “pear pro” features ETH + Wi-Fi + BLE/ETH + Wi-Fi mesh + BLE communication. This manual provides instructions for using this product to help users quickly start using it. This manual applies to the current software and hardware versions. We reserve the right to modify the manual content due to product upgrades. To prevent improper operation, please read this manual carefully before use.
სიმბოლოს აღწერა
For product installation tips, precautions, and potential hazards, we will use different symbols throughout this manual to alert you. Please pay special attention to these symbols while reading this manual and using the product. The following explains the symbols used – please read carefully.
მახასიათებლები
- Supports ETH, Wi-Fi, and BLE tri-mode communication
- Supports OTA firmware upgrades
- Supports automatic time synchronization via network
- Supports Wi-Fi Mesh networking protocol
- Wi-Fi supports 2.4G 802.11 b/g/n protocol
- Wi-Fi supports WPA/WPA2/WPA2-Enterprise encryption
- Supports E-Touch function (Android/iOS compatible)
- მხარს უჭერს BLE 4.2
- 3КВ large dual buffer for sending/receiving data
- Flame resistance rating: UL94 V-0
- UV resistance rating: UL746C F1
A. Interface: Connects to devices
B. Label: Displays product information
C. Red LED: Device communication indicator
D. Green LED: Network communication indicator
1. After the data logger is powered on, the red and green LED lights flash once per second
ერთდროულად.
2. For LED indicators details, see Chapter 10 [LED Status & Troubleshooting].5. Installation
This chapter describes how to install and remove the logger.
If only Wi-Fi communication is used, seal the Ethernet port with the solid waterproof
plug to ensure the data logger remains airtight. For specific methods, refer to Section
5.1 (Waterproof Plug Installation].
5.1.Install Waterproof Plug
install solid waterproof plug: As shown in the figure below, first install the solid waterproof plug
ბოლოში.
Figure 5-1-1 Installing Solid Waterproof Plug
5.2. Remove the waterproof plug:
Remove the Housing: As shown below, use a flat-head screwdriver to press the clips on both the
left and right sides of the logger, then pull off the housing.Figure 5-2-2 Inserting the Ethernet Cable
Install Housing and Waterproof Plug: As shown below, first reconnect the housing clips on both
sides of the logger. Then, clip the waterproof plug onto the Ethernet cable and insert it into the cable
port in the direction of the arrow.
Figure 5-2-3 Installing Housing and Plug
After Ethernet cable installation is complete, the result should look like the image below.
Figure 5-2-4 Completed Installation
5.3.Installing the logger
Install the data logger by aligning its anti-misalignment notch with the
corresponding notch on the device connector before insertion to prevent damage
to the data logger.5.4. Remove the logger
Loosen the Nut: As shown below, rotate the hex nut counter-clockwise until the threads are
completely disengaged.
Figure 5-4-1 Loosening the Nut
Pull Out the logger: As shown below, pull the collector out in the direction of the arrow. Removal
is now complete.7. Bluetooth connection
When configuring local parameters for the data logger or setting inverter parameters locally, you
need to establish a Bluetooth connection between your mobile device and the data logger. This section
explains how to pair them via Bluetooth.
The figure below illustrates the BLE connection setup. Please refer to Chapter 6: [APP download] to
install the corresponding APP, then follow the in-app instructions to configure the data logger. Ensure
the Bluetooth connection is successfully established before proceeding with configuration.
APP → BLE &
… ………••
≤ 10 მ
მობილური
მონაცემთა ლოგერი
Figure 7-1 BLE connection diagram
The effective Bluetooth communication range between the data logger and mobile device is 10
meters. For optimal performance, keep your phone as close as possible to the data logger during
operation.8. Network Connection
The product supports both Ethernet and Wi-Fi network connection methods. You may choose
either connection method based on your requirements. The following sections will introduce both
network connection approaches.
1. Ensure the logger is powered on during network configuration. If it is not powered,
check if the connected device is turned on
2. Ensure the router has a normal internet connection.
3. The logger has DHCP enabled by default. Please ensure the router’s DHCP function is
also enabled.
4. The logger communicates with the cloud server using ports 8886, 8885, and 80. Please
ensure these remote service access ports are open.
8.1. Configure Network Connection
8.1.1. Ethernet კავშირი
The figure below shows the Ethernet connection diagram of this product. If the router’s DHCP
function is enabled and the required ports are open, the data logger will automatically connect to the
network after Ethernet cable connection, without any configuration.
LAN
WLAN
Logger
როუტერი
სერვერი
Figure 8-1-1-1 Ethernet Connection Diagram
For static IP connection, refer to Chapter 8.2: [Network Parameter Settings] to modify the product’s
ქსელის პარამეტრები.
8.1.2. Wi-Fi Network Configuration
The figure below shows the Wi-Fi network configuration diagram via BLE for this product. Refer to
Chapter 6: [APP download] to install the corresponding APP, then follow the in-app instructions to
configure the data logger for proper network connection.
დოკუმენტები / რესურსები
 |
E-LINTER Pear Pro ETH Plus WiFi Plus BLE Stick მონაცემთა ჟურნალი [pdf] მომხმარებლის სახელმძღვანელო Pear Pro ETH Plus WiFi Plus BLE Stick მონაცემთა ლოგერი, ETH Plus WiFi Plus BLE Stick მონაცემთა ლოგერი, WiFi Plus BLE Stick მონაცემთა ლოგერი, BLE Stick მონაცემთა ლოგერი, Stick მონაცემთა ლოგერი |