TRACEABLE® CONTINUOUS
VISUAL ALARM TIMER
ინსტრუქციები
სპეციფიკაციები
= Audible alarm, audible key confirmation
= Visualalarm,visualkeyconfirmationმაღვიძარას დროის უკუთვლა
- If the timer is running, press the START/STOP button and then press the
და 
buttons simultaneously. The display should read 00 00. - დააჭირეთ button to advance the display, or press the button to decrease the display. (When the display reads 00 00, pressing the button will decrease the display to 99 99.)
- Once the desired time is on the display, press the START/STOP button to begin counting down. During countdown timing, the alarm will sound once (singleflashorbeep)every30secondstoindicatea30 second interval has passed.
- When the display reaches 00 00 the alarm will start (audible or visual depending on the alarm setting) and the timer will begin counting up.
During the first minute of alarming, the timer will alarm with increasing intensity. After the first minute, the timer will continue counting up and will alarm once (a single flash or beep) every 30 seconds until the alarm is stopped. The alarm may be stopped at any time by pressing any button.
While the timer is alarming–
დაჭერით
or button will stop the alarm, but will allow the timer to continue counting up.Pressing the START/STOP button will stop the alarm, stop the count up timing and will return the display to the originally programmed time.
მეხსიერების გახსენება
The memory function will recall the last programmed time. This feature allows the timer to be dedicated to a frequently timed test. The timer will return to the last programmed time again and again.
- მიჰყევით ნაბიჯებს 1-დან 4-მდე განყოფილებაში „უკუთვალავი განგაშის დრო“.
- When the alarm starts, press the START/STOP button to stop the alarm, stop the count up timing and return the display to the originally programmed time.
- Press the START/STOP button again to begin counting down.
ჩანაწერის გასწორება
If an error is made during an entry, press the და buttons simultaneously to clear the display to zero. Το clear an entry when time is running, stop the timing by pressing the START/STOP button, then press the და buttons simultaneously. The timer will only clear when time is stopped.
წამზომი (უკანასკნელი დათვლა) დროის აღრიცხვა
2. Press the START/STOP button to begin count-up timing.
Note: During the first 99 minutes 59 seconds of count-up time, the resolution is 1 second, after 100 minutes, the count-up resolution is 1 minute.
3. When timing has been completed and the timing has been stopped, press the and buttons simultaneously to clear the display to zero.
TIMEout
If this timer does not function properly for any reason, replace the batteries with new high quality batteries (see “Battery Replacement” section). Low battery power can occasionally cause any number of “apparent” operational difficulties. Replacing the batteries with a new fresh battery will solve most difficulties.
ბატარეის გამოცვლა
An incorrect display, no display or operational difficulties indicate that the batteries should be replaced. Slide open the battery cover on the back of the timer. Insert two new AAA size batteries. Make certain to note the proper polarity as indicated by the diagram in the battery compartment. Replace battery cover.
გარანტია, მომსახურება, ან კალიბრაცია
გარანტიის, მომსახურების ან დაკალიბრებისათვის დაუკავშირდით:
თვალთვალის პროდუქტები
12554 ძველი გალვესტონის რ. ლუქსი B230 Webსტერ, ტეხასი 77598 აშშ
დოქტორი 281 482-1714
ფაქსი 281 482-9448
ელ.ფოსტა support@traceable.com
www.traceable.com
Traceable Products are ISO 9001:2015 Quality-Certified by DNV and ISO/IEC
17025: 2017 აკრედიტირებული როგორც კალიბრაციის ლაბორატორია A2LA– ს მიერ.
Traceable and is a registered trademark of Cole-Parmer.
©2020 Traceable Products. 92-5133-00 რევ 5 071525
დოკუმენტები / რესურსები
 |
Visual Traceable 5133 Alarm Timer [pdf] მომხმარებლის სახელმძღვანელო 5133, 6876af4336218, 5133 Alarm Timer, 5133, Alarm Timer, Timer |